The Modal Shop, Inc. An MTS Company    Global Sales   Video   Newsletters   Library   About Us     
 
Home > Rental > Industrial IMI Sensors

Industrial IMI Sensors

IMI Sensors, a division of PCB Piezotronics, is a global designer and manufacturer of industrial vibration monitoring instrumentation such as accelerometers, vibration transmitters and switches. These industrial sensors are used to spot imbalance, bearing faults and misalignment by measuring machine vibration, providing early fault diagnosis thus reducing downtime.

Ruggedized accelerometers from PCB’s IMI Sensors feature stainless steel housings, a MIL-C-5015 connector and electrical case isolation to protect against electromagnetic interference, surface noise pickup and ground loop problems.

See calibration notes for information on calibration. Contact us for detailed selection assistance, or for unique requirements not shown.

 
Model
-3dB -10% -5% +5% +10% +3dB
608M31 250 20 0.5 - - - - 10k 0.001 5k -65 to +250 99.3
EX603C01 50 100 0.5 - - - - 10k 0.00035 5k -65 to +250 51  
628F01 50 100 0.3 0.67 1 4k 6.5k 12k 0.001 5k -65 to +250 94  
625B01 50 100 0.2 0.37 5 6.5k 7.5k 10.5k 0.00005 5k -65 to +250 145  
602D01 50 100 0.5 - - - - 8k 0.00035 5k -65 to +250 74  
608A11/030AC 50 100 0.5 - - - - 10k 0.00035 5k -65 to +250 99.3
607M03 50 100 0.43 0.87 1.2 5k 7k 10k 0.00075 5k -65 to +250 29
K333D01 20 100 0.155 1.5 2 8k 11k 22.9k 0.0025 7k 14 to +158 -  
333D01 20 100 0.155 1.5 2 8k 11k 22.9k 0.0025 7k 14 to +158 131  
VO622A01* - - 3 4 - - 4.5k 9k - 5k -65 to +250 94  

*Full Velocity Output Specifications

General Purpose     Back to Top

 

EX603C01
full specs

  • Intrinsically safe approved
  • 0.6875" hex stainless steel sensor
  • ±50g range
  • 51 gram mass
  • 1/4-28 female mounting
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A40 - 1/4-28 x 0.438" long stainless steel mounting stud with hex socket and brass tip
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

Similar to: B&K 8341, Dytran 3176B1, Endevco 5220B-100

 

628F01
full specs

  • 0.875" hex stainless steel sensor
  • ±50g range
  • 94 gram mass
  • 1/4-28 female mounting
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A40 - 1/4-28 x 0.438" long stainless steel mounting stud with hex socket and brass tip
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from at least 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ICS-1). See notes on calibration for additional information

Similar to: Dytran 3184E

 

625B01
full specs

  • 1.36" diameter stainless steel sensor
  • ±50g range
  • 145 gram mass
  • 1/4-28 male mounting (through-hole)
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A73 - 1/4-28 x 1.34" Captive mounting bolt
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from at least 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ICS-1). See notes on calibration for additional information

Similar to: Dytran 3184E

 

602D01
full specs

  • 1.65"x0.74"x0.845" stainless steel sensor
  • ±50g range
  • 74 gram mass
  • 1/4-28 male mounting (through-hole)
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A97 - 1/4-28 Captive mounting bolt
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from at least 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ICS-1). See notes on calibration for additional information

Similar to: Dytran 3184E

Integral Cable     Back to Top

 

608M31
full specs

  • Intrinsically safe approved
  • 0.5625" hex stainless steel sensor
  • ±250g range
  • 99.3 gram mass
  • 1/4-28 female mounting
  • 10ft Integral 2 pin MIL-C-5015 cable

Rental Includes:
081A40 - 1/4-28 x 0.438" long stainless steel mounting stud with hex socket and brass tip
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

Similar to: B&K 8341, Dytran 3176B1, Endevco 5220B-100

 

608A11/030AC
full specs

  • 0.5625" hex stainless steel sensor
  • ±250g range
  • 99.3 gram mass
  • 1/4-28 female mounting
  • 30ft Integral 2 pin MIL-C-5015 cable

Rental Includes:
081A40 - 1/4-28 x 0.438" long stainless steel mounting stud with hex socket and brass tip
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

 

607M03
full specs

  • 0.5625" hex stainless steel sensor
  • ±250g range
  • 29 gram mass
  • 1/4-28 male mounting
  • 30ft Integral 2 pin MIL-C-5015 cable

Rental Includes:
080A156 - 1/2-20 to 1/4-28 mounting stud with hex socket
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

Digital Sensor     Back to Top

Plug a ruggedized full piezoelectric accelerometer directly into your computer, tablet or phone for quick spot checks. Rental options include renting the sensor only (many software options available from Digiducer.com) or as a kit with a tablet and software installed.

 

K333D01 Single Channel Vibration Monitoring Kit
full specs

  • System Controller (typically an iPad) loaded with vibration monitoring software
  • 1.0" hex stainless steel sensor
  • ±20g range
  • 1/4-28 male mounting
  • 10ft Integral USB cable

Rental Includes:
System Controller - (typically an iPad) loaded with vibration monitoring software
333D01 - Digiducer
080A156- 1/2-20 to 1/4-28 mounting stud with hex socket

Optional Accessories, Rented Separately:
080A121 - Flat Surface Magnet Base
080A131 - Curved Surface Magnet Base
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

 

333D01
full specs

  • 1.0" hex stainless steel sensor
  • ±20g range
  • 131 gram mass
  • 1/4-28 male mounting
  • 10ft Integral USB cable

Rental Includes:
080A156 - 1/2-20 to 1/4-28 mounting stud with hex socket
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

Velocity Output Sensor     Back to Top

 

VO622A01
full specs

  • 7/8" hex stainless steel sensor
  • ± 50 in/sec range
  • 94 gram mass
  • 1/4-28 male mounting
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A40 - 1/4-28 x 0.438" mounting stud with hex socket
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

Notes on Calibration     Back to Top

Calibration data is provided electronically (on CD or USB memory stick) or as printed copies, depending on quantity rented and end-user preference.

The Modal Shop has internal calibration intervals set for most test products at 1 year. ANSI/ISO/IEC 17025:2000 makes clear that it is the responsibility of the end-user organization (in this case, the renter) to determine the appropriate calibration interval under the requirements of its own quality system. Per this, calibration certificates of rented equipment have "calibrated on" dates, but blank "calibration due" dates. Rentals ship with a customer specific expected return date in mind - if equipment is expected out for 5 months, the last calibration date will be within the past 7 months. Calibration to additional standards (e.g. Z540 or specific FAA requirements) are possible, but there may be an additional charge.

The Modal Shop's Scope of Accreditation can be found here. An example of a calibrations certificate can be found here. Please contact us with questions or if a different calibration will be needed for your rental sensors.

Notes on TEDS (Transducer Electronic Data Sheet)     Back to Top

The TEDS option is available on several rental transducers. TEDS stands for Transducer Electronic Data Sheet and provides memory within a sensor with manufacturer name, sensor type, model number, serial number and calibration data. It is an approved IEEE standard (1451.4), and many data acquisition manufacturers include the ability to read TEDS sensors. Not sure if your DAQ has TEDS capability? No problem; TEDS sensors can be used alongside non-TEDS sensors with no issues; the TEDS memory is bypassed. Want more information? See our TEDS FAQ .