The Modal Shop, Inc. A PCB Group Co.    Global Sales   Video   Newsletters   Library   About Us  
 
Home > Rental > Single Axis ICP Accelerometers

Single Axis ICP Accelerometers

Single direction, single axis units. Generally, start the selection with the maximum g amplitude range in mind. Next, verify other factors including temperature, range, mounting type, and cable configuration. Or browse the Shock, Miniature, General Purpose, Modal Array, or Industrial accelerometer sections. For multi-axis testing, consider a triaxial unit or use a triaxial mounting adaptor(see accessories). See calibration notes for information on calibration. Contact us for detailed selection assistance, or for unique requirements not shown.

For high temperature sensors please see the high temperature accelerometer page.

Model
-3dB -10% -5% +5% +10% +3dB
350B21* 100k 0.05 0.5 1 - - 10k 35k 0.3 200k -65 to +200 4.4  
350D02* 50k 0.1 2 4 - - 10k 25k 0.5 150k 0 to +150 4.5  
350M90* 25k 0.1 2 4 - - 10k 25k 0.5 150k 0 to +150 4.5  
350C03* 10k 0.5 0.2 0.4 - - 10k 25k 0.04 50k 0 to +150 5.4  
350C04* 5k 1 0.2 0.4 - - 10k 25k 0.02 50k 0 to +150 5.4  
352B70 5k 1 0.4 - 0.7 9k - 20k 0.025 10k -65 to +250 4.3
352A25 2k 2.5 0.3 0.7 1 10k 13k 20k 0.01 10k -65 to +250 0.6  
352C23 1k 5 0.7 1.5 2 10k 15k 25k 0.003 10k -65 to +250 0.2  
352A60 500 10 5 - - - - 60k 0.002 5k -65 to +250 6  
352C22 500 10 0.3 0.7 1 10k 13k 20k 0.0015 10k -65 to +250 0.5  
352A21 500 10 0.3 0.7 1 10k 13k 20k 0.004 10k -65 to +250 0.6  
353B15 500 10 0.35 0.7 1 10k 18k 30k 0.005 10k -65 to +250 2
353B17 500 10 0.35 0.7 1 10k 17k 30k 0.005 10k -65 to +325 1.7
353B18 500 10 0.35 0.7 1 10k 18k 30k 0.005 10k -65 to +250 1.8
353B03 500 10 0.35 0.7 1 7k 11k 20k 0.003 10k -65 to +250 10.5
353B04 500 10 0.35 0.7 1 7k 11k 20k 0.003 10k -65 to +250 10.5
352A24 50 100 0.4 0.8 1 8k 10k 12k 0.002 5k -65 to +250 0.8  
352C65 50 100 0.2 0.3 0.5 10k 12k 20k 0.00016 5k -65 to +200 2
352C68 50 100 0.2 0.3 0.5 10k 12k 20k 0.00016 5k -65 to +200 2
353B33 50 100 0.35 0.7 0.1 4k 6.5k 12k 0.0005 10k -65 to +250 27
T333B32 50 100 - - 0.5 3k - - 0.00015 5k -0 to +150 4  
333B 50 100 - - 2 1k - - 0.00007 3.5k -0 to +150 5.6  
T333B 50 100 - - 2 1k - - 0.00007 3.5k -0 to +150 5.6  
EX603C01 50 100 0.5 - - - - 10k 0.00035 5k -65 to +250 51  
628F01 50 100 0.3 0.67 1 4k 6.5k 12k 0.001 5k -65 to +250 94  
625B01 50 100 0.2 0.37 5 6.5k 7.5k 10.5k 0.00005 5k -65 to +250 145  
602D01 50 100 0.5 - - - - 8k 0.00035 5k -65 to +250 74  
351B41 15 100 0.35 0.7 1 2k 3.5k 5k 0.0005 1k -320 to +250 40
TLD333B50 5 1000 - - 0.5 3k - - 0.00005 4k 0 to +150 7.5

*350 series sensors frequency ranges specified at ±3 dB and ±1 dB range

Shock Accelerometers
Back to Top

Designed to withstand and measure extreme high-level, short-duration transient accelerations, units also feature internal filtering for resonance suppression. Applications include metal-to-metal tests, impacts and armor testing, explosive studies, pile driver monitoring, and simulated pyroshock events. High-g shock calibration is included with rental of 350 Series units.

 

350B21
full specs

  • 0.375" hex titanium sensor
  • ±100000g range
  • 4.4 gram mass
  • 1/4-28 integral stud mounting
  • 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Rental Includes:
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration; includes 10g frequency response to upper 1dB point (TMS: MCS-A001 or PCB ACS-22) and high g shock (TMS: MCS-31 or PCB: ACS-14). See notes on calibration for additional information

Similar to: B&K 8339-002, Dytran 3200B,  Kistler 8743A100

 

350D02
full specs

  • 0.375" hex titanium sensor
  • ±50000g range
  • 4.5 gram mass
  • 1/4-28 integral stud mounting
  • 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Rental Includes:
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration; includes 10g frequency response to upper 1dB point (TMS: MCS-A001 or PCB ACS-22) and high g shock (TMS: MCS-31 or PCB: ACS-14). See notes on calibration for additional information

Similar to: B&K 8339-001, Dytran 3200B2, Endevco 2255B & 7255A, Kistler 8743A50 & 8742A50

 

350M90
full specs

  • 0.375" hex titanium sensor
  • ±25000g range
  • 4.5 gram mass
  • 1/4-28 integral stud mounting
  • 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Rental Includes:
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration; includes 10g frequency response to upper 1dB point (TMS: MCS-A001 or PCB ACS-22) and high g shock (TMS: MCS-31 or PCB: ACS-14). See notes on calibration for additional information

Similar to: B&K 8339-001, Dytran 3200B2, Endevco 2255B & 7255A, Kistler 8743A50 & 8742A50

 

350C03
full specs

  • 0.375" hex titanium sensor
  • ±10000g range
  • 5.4 gram mass
  • 1/4-28 integral stud mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C series cables

Rental Includes:
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration; includes 10g frequency response to upper 1dB point (TMS: MCS-A001 or PCB ACS-22) and high g shock (TMS: MCS-31 or PCB: ACS-14). See notes on calibration for additional information

Similar to: Dytran 3200B5, Endevco 2255B-1 & 7255A-1, Kisltler 8743A5 & 8742A5

 

350C04
full specs

  • 0.375" hex titanium sensor
  • ±5000g range
  • 5.4 gram mass
  • 1/4-28 integral stud mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C series cables

Rental Includes:
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration; includes 10g frequency response to upper 1dB point (TMS: MCS-A001 or PCB ACS-22) and high g shock (TMS: MCS-31 or PCB: ACS-14). See notes on calibration for additional information

Similar to: Dytran 3200B5, Endevco 2255B-1 & 7255A-1, Kisltler 8743A5 & 8742A5

 

352B70
full specs

  • 0.375" hex titanium sensor
  • ±5000g range
  • 4.5 gram mass
  • 10-32 female mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C series cable

Rental Includes:
080A04-Adhesive mounting base, 0.37" hex x 0.2" thk, 10-32 tapped hole, aluminum w/insulating hardcoat finish
081B05-10-32 to 10-32 adaptor stud
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration; includes 10g frequency response to upper 1dB point (TMS: MCS-A001 or PCB ACS-22) and high g shock (TMS: MCS-31 or PCB: ACS-14). See notes on calibration for additional information

Similar to: Dytran 3200B5T, Kistler 8704B5000

Miniature Accelerometers
Back to Top

Lightweight units are ideal for high frequency testing with a small size and low mass. Applications include environmental testing, component qualification, structural testing and operational behavior of lightweight or thin objects, and fatigue testing.

! When removing teardrop style sensors, it is essential to use the removal tool supplied along with an appropriate debonding agent.

   

352A25
full specs

  • 0.45"x0.25"x0.14" Titanium sensor
  • ±2000g range
  • 0.6 gram mass
  • Adhesive mounting
  • 3-56 coaxial jack electrical connector. Included 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Technique video for installation and removal of miniature accelerometers is key to obtaining valid measurements and to avoid damage to the accelerometer.

Rental Includes:
030A10-10-ft detachable cable. 3-56 plug to 10-32 plug
039A27-Removal tool
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4516-001, Endevco 25A, 25B, 7625A & 2250A-10

   

352C23
full specs

  • 0.34"x0.16"x0.11" anodized aluminum sensor
  • ±1000g range
  • 0.2 gram mass
  • Adhesive mounting
  • 3-56 coaxial jack electrical connector. Included 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Technique video for installation and removal of miniature accelerometers is key to obtaining valid measurements and to avoid damage to the accelerometer.

Rental Includes:
030A10-10-ft detachable cable. 3-56 plug to 10-32 plug
039A26-Removal tool
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4516-001, Endevco 25A & 25B & 7625A

   

352A21
full specs

  • 0.45"x0.25"x0.14" Titanium sensor
  • ±1000g range
  • 0.6 gram mass
  • Adhesive mounting
  • 3-56 coaxial jack electrical connector. Included 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Technique video for installation and removal of miniature accelerometers is key to obtaining valid measurements and to avoid damage to the accelerometer.

Rental Includes:
030A10-10-ft detachable cable. 3-56 plug to 10-32 plug
039A27-Removal tool
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4516-001, Endevco 25A & 25B & 7625A

   

352C22
full specs

  • 0.45"x0.25"x0.14" anodized aluminum sensor
  • ±500g range
  • 0.5 gram mass
  • adhesive mounting
  • 3-56 coaxial jack electrical connector. Included 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Technique video for installation and removal of miniature accelerometers is key to obtaining valid measurements and to avoid damage to the accelerometer.

Rental Includes:
030A10-10-ft detachable cable. 3-56 plug to 10-32 plug
039A26-Removal tool
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4517,  Dytran 3224A1, Endevco 27A11 & 27AM1-10 & 2250A & 2222C (charge type), Kistler 8778A500

   

352A24
full specs

  • 0.48"x0.28"x0.19" anodized aluminum sensor
  • ±50g range
  • 0.8 gram mass
  • adhesive mounting
  • 3-56 coaxial jack electrical connector. Included 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Technique video for installation and removal of miniature accelerometers is key to obtaining valid measurements and to avoid damage to the accelerometer.

Rental Includes:
030A10-10-ft detachable cable. 3-56 plug to 10-32 plug
039A26-Removal tool
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: Dytran 3225M24, Endevco 27A12 & 27AM1-100 & 2222D (charge type)

General Purpose Accelerometers
Back to Top

These units cover a wide range of tests ranging from vibration control to machine testing, and product qualification. Sensors detailed measure either ±50g or ±500g ranges, but piezoelectric accelerometers often measure an extremely high dynamic range and are perfectly suited for measurements of quite low vibration levels.

 

352A60
full specs

  • 0.375" hex stainless steel sensor
  • ±500g range
  • 6 gram mass
  • 10-32 integral stud mounting
  • 5-44 coaxial jack electrical connector used with 003P or 018C cable series

Rental Includes:
030A10-10-ft detachable cable. 3-56 plug to 10-32 plug
039A26-Removal tool
Calibration - Special

 

 

353B15
full specs

  • 0.31" hex titanium sensor
  • ±500g range
  • 2 gram mass
  • 5-40 integral stud mounting
  • 5-44 coaxial jack electrical connector used with 003P or 018C cable series

Rental Includes:
080A15-Adhesive mounting base, 0.312" hex x 0.125" thk, 5-40 tapped hole, aluminum w/insulating hardcoat finish
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4519, Dytran 3035B1, Endevco 256-10, Kistler 8720A500

 

353B17
full specs

  • 0.28" hex titanium sensor
  • ±500g range
  • 1.7 gram mass
  • 5-40 integral stud mounting
  • 10-ft integral cable terminating in 10-32 plug. Use 070A02 scope adaptor to terminate in BNC, or use 070A05 cable connector to 002C or 003C series cable.

Rental Includes:
080A15-Adhesive mounting base, 0.312" hex x 0.125" thk, 5-40 tapped hole, aluminum w/insulating hardcoat finish
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

 

 

353B18
full specs

  • 0.28" hex titanium sensor
  • ±500g range
  • 1.8 gram mass
  • 5-40 integral stud mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
080A15-Adhesive mounting base, 0.312" hex x 0.125" thk, 5-40 tapped hole, aluminum w/insulating hardcoat finish
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4518, Dytran 3145A1, Kistler 8730A500

 

353B03
full specs

  • 0.5" hex titanium sensor
  • ±500g range
  • 10.5 gram mass
  • 10-32 female mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
080A-Adhesive mounting base, 0.5" hex x 0.187" thk, 10-32 tapped hole, aluminum w/insulating hardcoat finish
081B05-10-32 to 10-32 adaptor stud
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: Dytran 3056B1, Kistler 8704B500

 

353B04
full specs

  • 0.5" hex titanium sensor
  • ±500g range
  • 10.5 gram mass
  • 10-32 female mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
080A-Adhesive mounting base, 0.5" hex x 0.187" thk, 10-32 tapped hole, aluminum w/insulating hardcoat finish
081B05-10-32 to 10-32 adaptor stud
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: Dytran 3056B1, Kistler 8704B500

 

352C65
full specs

  • 0.312" hex titanium sensor
  • ±50g range
  • 2 gram mass
  • 5-40 integral stud mounting
  • 5-44 coaxial jack electrical connector used wiht 003P or 018C cable series

Rental Includes:
080A15-Adhesive mounting base, 0.5" hex x 0.187" thk, 10-32 tapped hole, aluminum w/insulating hardcoat finish
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4519-001, Dytran 3035B, Endevco 256-100, Kistler 8776A50

 

352C68
full specs

  • 0.28" hex titanium sensor
  • ±50g range
  • 2 gram mass
  • 5-40 integral stud mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
080A15-Adhesive mounting base, 0.5" hex x 0.187" thk, 10-32 tapped hole, aluminum w/insulating hardcoat finish
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4518-001, Dytran 3145A, Kistler 8774A50

 

353B33
full specs

  • 0.75" hex titanium sensor
  • ±50g range
  • 27 gram mass
  • 10-32 female mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
080A15-Adhesive mounting base, 0.5" hex x 0.187" thk, 10-32 tapped hole, aluminum w/insulating hardcoat finish
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4518-001, Dytran 3145A, Kistler 8774A50

 

351B41
full specs

  • Cryogenic ICP sensor useable to -320°F (-196°C)
  • 0.75" hex titanium sensor
  • ±15g range
  • 40 gram mass
  • 10-32 female mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
081B05-10-32 to 10-32 adaptor stud
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Modal Array Accelerometers
Back to Top

Excellent phase characteristics and lightweight construction, ideal for structural vibration, multi-channel modal analysis, analytical model correlation, and force-response testing. Many units have TEDS functionality as an option, see information below. A wide range of structural test hardware is also available, including shakers and impact hammers, as well as large-channel cable management solutions.

 

T333B32 (TEDS version)
full specs

  • 0.4"x0.63"x0.4" titanium cube sensor
  • ±50g range
  • 4 gram mass
  • adhesive mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: B&K 4507-002, Dytran 3097A2, Kistler 8640A50

 

333B
TEDS version available (TEDS notes)
full specs

  • 0.48" diameter polymer sensor
  • ±50g range
  • 5.6 gram mass
  • adhesive base mounting
  • 3 pin socket connector used with 080B cable series

Rental Includes:
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

 

 

TLD333B50
full specs

  • 0.45" titanium cube sensor
  • ±5g range
  • 7.5 gram mass
  • 5-40 female mounting
  • 10-32 coaxial jack electrical connector used with 002C or 003C cable series

Rental Includes:
080A25-Adhesive mounting base, 0.438" hex, 5-40 tapped hole, aluminum hardcoat
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ACS-1). See notes on calibration for additional information

Similar to: Kistler 8640A5

IMI Industrial Accelerometers
Back to Top

Ruggedized accelerometers from PCB’s IMI Sensors feature stainless steel housings, a MIL-C-5015 connector and electrical case isolation to protect against electromagnetic interference, surface noise pickup and ground loop problems.

 

EX603C01
full specs

  • Intrinsically safe approved
  • 0.6875" hex stainless steel sensor
  • ±50g range
  • 51 gram mass
  • 1/4-28 female mounting
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A40 - 1/4-28 x 0.438" long stainless steel mounting stud with hex socket and brass tip
Calibration - NIST traceable and ISO 17025/A2LA accredited single point amplitude response calibration at 6000cpm (100Hz) (TMS: MCS-A002 or PCB: ICS-2). See notes on calibration for additional information

Similar to: B&K 8341, Dytran 3176B1, Endevco 5220B-100

 

628F01
full specs

  • 0.875" hex stainless steel sensor
  • ±50g range
  • 94 gram mass
  • 1/4-28 female mounting
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A40 - 1/4-28 x 0.438" long stainless steel mounting stud with hex socket and brass tip
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ICS-1). See notes on calibration for additional information

Similar to: Dytran 3184E

 

625B01
full specs

  • 1.36" diameter stainless steel sensor
  • ±50g range
  • 145 gram mass
  • 1/4-28 male mounting (through-hole)
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A73 - 1/4-28 x 1.34" Captive mounting bolt
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ICS-1). See notes on calibration for additional information

Similar to: Dytran 3184E

 

602D01
full specs

  • 1.65"x0.74"x0.845" stainless steel sensor
  • ±50g range
  • 74 gram mass
  • 1/4-28 male mounting (through-hole)
  • 2 pin MIL-C-5015 electrical connector used with 012E cable series

Rental Includes:
081A97 - 1/4-28 Captive mounting bolt
Calibration - NIST traceable and ISO 17025/A2LA accredited calibration from 10 Hz to upper 5% point (TMS: MCS-A001 or PCB: ICS-1). See notes on calibration for additional information

Similar to: Dytran 3184E

Notes on Calibration
Back to Top

Calibration data is provided electronically (on CD or USB memory stick) or as printed copies, depending on quantity rented and end-user preference.

The Modal Shop has internal calibration intervals set for most test products at 1 year. ANSI/ISO/IEC 17025:2000 makes clear that it is the responsibility of the end-user organization (in this case, the renter) to determine the appropriate calibration interval under the requirements of its own quality system. Per this, calibration certificates of rented equipment have "calibrated on" dates, but blank "calibration due" dates. Rentals ship with a customer specific expected return date in mind - if equipment is expected out for 5 months, the last calibration date will be within the past 7 months. Calibration to additional standards (e.g. Z540 or specific FAA requirements) are possible, but there may be an additional charge.

The Modal Shop's Scope of Accreditation can be found here. An example of a calibrations certificate can be found here. Please contact us with questions or if a different calibration will be needed for your rental sensors.

Notes on TEDS (Transducer Electronic Data Sheet)
Back to Top

The TEDS option is available on several rental transducers. TEDS stands for Transducer Electronic Data Sheet and provides memory within a sensor with manufacturer name, sensor type, model number, serial number and calibration data. It is an approved IEEE standard (1451.4), and many data acquisition manufacturers include the ability to read TEDS sensors. Not sure if your DAQ has TEDS capability? No problem; TEDS sensors can be used alongside non-TEDS sensors with no issues; the TEDS memory is bypassed. Want more information? See our TEDS FAQ .